Nec NL3224AC35-01 LCD Panel
33.355,40 TL
DATA SHEET
TFT COLOR LCD MODULE
NL3224AC35-01, 13
14 cm (5.5 inches), 320 ´ 240 Pixels, Full color
NTSC/PAL mode, Wide temperature range
DESCRIPTION
NL3224AC35-01 and NL3224AC35-13 are TFT (thin film transistor) active matrix color liquid crystal displays (LCD)
comprising amorphous silicon TFT attached to each signal electrode, a driving circuit and a backlight. Both the
products have a built-in backlight.
Their 14 cm diagonal display area contain 320 ´ 240 pixels and can display full-color simultaneously.
The difference between NL3224AC35-01 and NL3224AC35-13 is as follows:
• NL3224AC35-01: Antiglare polarizer surface
• NL3224AC35-13: Smoth polarizer surface
FEATURES
• High luminance
• NTSC/PAL mode
• Reversible horizontal and vertical scanning
• 234/240 line display
• Wide temparature range
• Analog RGB interface
• Incorporated edge type backlight
APPLICATIONS
• Car navigations
• TV monitors
• Video games
• Monitors for process controller
The information in this document is subject to change without notice.
Please confirm with the delivery specification before statting to design the system.
Document No. EN0495EJ1V1DS00
Date Published April 2000 P
Printed in Japan
2000
NL3224AC35-01, 13
STRUCTURE AND FUNCTIONS
A TFT color LCD module comprised a TFT LCD panel, LSIs for driving liquid crystal, and a backlight. The
TFT LCD panel is composed of a TFT array glass substrate superimposed on a color filter glass substrate with
liquid crystal filled in the narrow gap between two substrates. The backlight apparatus is located on the backside
of the LCD panel.
RGB (Red, Green, Blue) data signals are sent to LCD panel drivers after modulation into suitable forms for
active matrix addressing through signal processor.
Each of the liquid crystal cells acts as an electro-optical switch that controls the light transmission from the
backlight by a signal applied to a signal electrode through the TFT switch.
OUTLINE OF CHARACTERISTICS (at room temperature)
Items Description
Display area 111.36 (H) ´ 83.52 (V) mm
Drive system a-Si TFT active matrix
Display colors Full-color
Number of pixels 320 ´ 240
Pixel arrangement RGB vertical stripe
Pixel pitch 0.348 (H) ´ 0.348 (V) mm
Module size 134.0 (H) ´ 110.0 (V) ´ 23.0 max. (D) mm
Weight 315 g (typ.)
Contrast ratio 85:1 (typ.)
Viewing angle
(more than the contrast
ratio of 10:1)
• Horizontal: 45° (typ. left side, right side)
• Vertical: 30° (typ. up side), 15° (typ. down side)
Designed viewing direction • wider viewing angle with contrast ratio : up side (12 o’clock)
• wider viewing angle without image reversal : down side (6 o’clock)
• optimum grayscale (g = 2.2) : perpendicular
Color gamut 50 % (typ. center, to NTSC)
Response time 16 ms (typ.), "white” to "black”
Luminance 250 cd/m2 (typ.)
Signal system Analog RGB signals, synchronous signals (CLK, HS, VS)
Backlight Edge light type, one fluorescent lamp (cold cathode type)
Back-Light Unit. (Parts No.: 55LHS-1)
Supply voltage 9.5 V (LCD power supply), 9.5 V (Backlight power supply)
Power consumption 6.6 W (typ.)
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
BLOCK DIAGRAM OF BASIC STRUCTURE
Video circuit board
DC
clamp
Gamma
correction
AMP
DC
shift
H-Driver
Analog RGB
V-Driver
+
Controller
Panel
MUTE
Video
select
Clamp pulse
HS
VS
COM
signal
234/240 select
Reversible select
• horizontal
• vertical
NTSC/PAL select
Inverter backlight
Luminance control
VDCB
VDC ICS
Drivers
GNDA
GNDD
Analog
SW
DC/DC
converter
Note 1. Frame is contacted with both GNDA and GNDD
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
GENERAL SPECIFICATIONS
Items Description Unit
Module size 134.0 ± 0.5 (H) ´ 110.0 ± 0.5 (V) ´ 23.0 max. (D) mm
Display area 111.36 (H) ´ 83.52 (V) mm
Number of dots 320 ´ 3 (H) ´ 240 (V) dot
Dot pitch 0.116 (H) ´ 0.348 (V) mm
Pixel pitch 0.348 (H) ´ 0.348 (V) mm
Pixel arrangement RGB (Red, Green, Blue) vertical stripe –
Display colors Full-color color
Weight 330 (max.) g
Note An inverter is incorporated with the module.
ABSOLUTE MAXIMUM RATINGS
Parameters Symbols Ratings Unit Remarks
Supply voltage VDC –0.5 to 20.0 V Ta = 25°C
VDCB –0.5 to 20.0 V
Analog RGB
input signal
VIN1 –2.5 to 2.5 V Ta = 25°C
VDC = 9.5 V
Logic input voltage VIN2 –0.5 to 5.5 V
Storage temp. TST –40 to 95 °C –
Operating temp. TOP –30 to 85 °C Note 1
Relative humidity (RH) <= 95 % Ta <= 40°C no
condensation<= 85 % 40 < Ta <= 50°C
Absolute humidity Absolute humidity shall not
exceed Ta = 50°C, RH = 85%
g/m3 Ta > 50°C
Note 1. Module surface: measured at the display center.
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
ELECTRICAL CHARACTERISTICS
(1) Power supply, logic input
Ta = 25°C
Parameters Symbol Min. Typ. Max. Unit Remarks
Supply voltage VDC 8.0 9.5 13.0 V For processor,
controller and driver
VDCB 8.0 9.5 13.0 V For backlight
Logic input "L” voltage VIL 0 – 0.9 V –
Logic input "H” voltage VIH 3.15 – 5.0 V
Logic output "L” voltage VOL 0 – 0.3 V
Logic output "H” voltage VOH 4.5 – 5.0 V
Supply current IDC – 147 200 mA At dot-checkered pattern
(VDC = 9.5 V)
IDCB – 541 600 mA Maximum luminance
(VDCB = 9.5 V)
(2) Analog RGB signals
Ta = 25°C
Parameters Min. Typ. Max. Unit Remarks
Analog RGB input voltage (white - black) 0 – 0.7 Vp-p Zi = 75 W
DC input level (black level) –1.0 – 1.0 V
SUPPLY VOLTAGE SEQUENCE
VDCBNote1
Logic signalsNote2
VDCNote3
0 < < 30 ms
0 < < 200 msNote4
0 < < 30 ms time
0 < < 200 msNote4
Notes 1.
Apply VDCB within the LCD operation period. When the backlight turns on before LCD operation or the
LCD operation turns off before the backlight turns off, the display may momentarily become white.
2.
When the VDC is off, please keep whole logic signals at "0 V.” In case of the signal more than "0.3 V,”
internal circuit may get damaged.
3.
Please turn off VDC when the signals are put off. If the signals are put off without keep VDC, the display
may be un-uniformity.
4.
Reference value.
5.
While the power is off, please keep whole signals (HS, VS, EXTCLK) at low level or high impedance.
6.
Wrong power sequence may damage to the module.
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
INTERFACE PIN CONFIGURATION
(1) Connector (CN1)
Part no. : 52610-3090
Supplier : Molex
Adaptable cable : SUMI-CARD 1.0 mm pitch 30 wick 85°C quality
Supplier : SUMITOMO ELECTRIC INDUSTRIES, LTD.
Pin No. Symbol Pin No. Symbol Pin No. Symbol
1 GNDD 11 EXTCSL 21 GNDD
2 EXTCLK 12 GNDD 22 GNDD
3 GNDD 13 N/P 23 GNDD
4 HS 14 MTSL 24 GNDA
5 VS 15 U/D 25 R
6 HOUT 16 R/L 26 GNDA
7 VOUT 17 GNDD 27 G
8 BPLS 18 VDCB 28 GNDA
9 GNDD 19 VDCB 29 B
10 GNDD 20 VDC 30 GNDA
Upper side
CN1
1
30
Lower side
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
PIN DESCRIPTION
Symbols In/Out Logics Description
EXTCLK In Note 1 – External clock
EXTCLK becomes active, when EXTCSL is "H"
EXTCSL In Note 1 Positive Clock select signal H: External clock
Default value is L L: Internal clock
HS In Note 1 Negative Horizontal synchronous signal
VS In Note 1 Negative Vertical synchronous signal
HOUT Out Note 1 Negative Horizontal synchronous signal output
VOUT Out Note 1 Negative Vertical synchronous signal output
R In – Analog Red signal 0.7 Vp-p Zi = 75 W
G In – Analog Green signal 0.7 Vp-p Zi = 75 W
B In – Analog Blue signal 0.7 Vp-p Zi = 75 W
R/L In Note 1 – Horizontal scanning select signal H: Right scanning
Default value is L L: Left scanning
U/D In Note 1 – Vertical scanning select signal H: down scanning
Default value is L L: up scanning
N/P In Note 1 – Display mode select H: PAL mode
Default value is L L: NTSC mode
MTSL In Note 1 – Vertical display area select signal H: 240 lines
Default value is L L: 234 lines
BPLS In Note 1 – Luminance control signal (pulse input)
Luminance is controlled by the pulse width.
Duty 100%: luminance Max. Refer to P17 (note 8).
VDC In – Power supply for processor, controller and driver (+9.5 V)
VDCB In – Power supply for backlight (+9.5 V)
GNDA – Note 2 – Ground for analog RGB signal
GNDD – Note 2 – Ground for logic (VDC) and backlight (VDCB)
Notes 1. CMOS level
2. GNDA should be separated from GNDD to aboid display noise.
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
SIGNALS
No. Functions Description
1 Reversible horizontal scanning R/L signal is able to reverse scanning direction.
(Right ® Left or Left ® Right)
2 Reversible vertical scanning U/D signal is able to reverse scanning direction.
(Up ® Down or Down ® Up)
3 NTSC/PAL mode N/P signal is able to change operating mode.
(NTSC ® PAL or PAL ® NTSC)
Scanning line is thinned out at the rate of seven to six lines in the PAL mode.
4 234/240 line display MTSL signal is able to change scanning line.
(234 lines ® 240 lines or 240 lines ® 234 lines)
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
INPUT SIGNAL TIMING
(1) mode
(a) NTSC, internal CLK
Parameters Symbols Min. Typ. Max. Unit Remarks
Internal-CLK Frequency 1/tc –
–
6.36
157.32
–
–
MHz
ns
–
Rise/fall tcrf – – 70 ns –
Duty tch/tc 0.4 0.5 0.6 – –
HS Frequency th 60.38
–
63.56
404
66.74
–
ms
CLK
15.734 kHz
(typ.)
Display thd –
–
50.34
320
–
–
ms
CLK
–
Pulse-width thp 1.0
–
4.7
30
–
–
ms
CLK
–
Pulse-width
+back-porch
thpb –
–
11.01
70
–
–
ms
CLK
234 line
–
–
12.11
77
–
–
ms
CLK
240 line
CLK-Hsync timing
hold/setup time
thch 10.0 – – ns –
thcs 10.0 – – ns –
V-Hsync timing
hold/setup time
thvh 1 – – CLK –
thvs 10.0 – – ns –
Rise/fall thrf – – 10.0 ns –
VS Frequency tv 15.85
–
16.68
262.5
17.51
–
ms
H
59.94 Hz
(typ.)
Display tvd –
–
14.87
234
–
–
ms
H
234 line
–
–
15.25
240
–
–
ms
H
240 line
Pulse-width tvp 158.89
–
190.67
3
–
–
ms
H
–
Pulse-width
+back-porch
tvpb –
–
1.33
21
–
–
ms
H
–
Rise/fall tvrf – – 10.0 ns –
Note In the display start period (pulse-width + back-porch), analog RGB signals should be blanking level.
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
(b) PAL, internal CLK
Parameters Symbols Min. Typ. Max. Unit Remarks
Internal-CLK Frequency 1/tc –
–
6.45
154.96
–
–
MHz
ns
–
Rise/fall tcrf – – 70 ns –
Duty tch/tc 0.4 0.5 0.6 – –
HS Frequency th 60.80
–
64.00
413
67.20
–
ms
CLK
15.625 kHz
(typ.)
Display thd –
–
49.60
320
–
–
ms
CLK
–
Pulse-width thp 1.0
–
4.7
30
–
–
ms
CLK
–
Pulse-width
+back-porch
thpb –
–
11.93
77
–
–
ms
CLK
234 line
–
–
12.71
82
–
–
ms
CLK
240 line
CLK-Hsync timing
hold/setup time
thch 10.0 – – ns –
thcs 10.0 – – ns –
V-Hsync timing
hold/setup time
thvh 1 – – CLK –
thvs 10.0 – – ns –
Rise/fall thrf – – 10.0 ns –
VS Frequency tv 19.00
–
20.00
312.5
21.00
–
ms
H
50.00 Hz
(typ.)
Display tvd –
–
17.47
273
–
–
ms
H
234 line
–
–
17.92
280
–
–
ms
H
240 line
Pulse-width tvp 153.60
–
192.00
2.5
–
–
ms
H
–
Pulse-width
+back-porch
tvpb –
–
1.86
29
–
–
ms
H
234 line
–
–
1.66
26
–
–
ms
H
240 line
Rise/fall tvrf – – 10.0 ns –
Note In the display start period (pulse-width + back-porch), analog RGB signals should be blanking level.
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
(c) NTSC, external CLK
Parameters Symbols Min. Typ. Max. Unit Remarks
EXTCLK Frequency 1/tc –
118.75
8.0
125.00
–
131.25
MHz
ns
–
Rise/fall tcrf – – 10 ns –
Duty tch/tc 0.4 0.5 0.6 – –
HS Frequency th 60.38
–
63.56
508
66.74
–
ms
CLK
15.734 kHz
(typ.)
Display thd –
–
40.00
320
–
–
ms
CLK
–
Pulse-width thp 1.0
–
4.7
38
–
–
ms
CLK
–
Pulse-width
+back-porch
thpb –
–
8.75
70
–
–
ms
CLK
234 line
–
–
9.63
77
–
–
ms
CLK
240 line
CLK-Hsync timing
hold/setup time
thch 10.0 – – ns –
thcs 10.0 – – ns –
V-Hsync timing
hold/setup time
thvh 1 – – CLK –
thvs 10.0 – – ns –
Rise/fall thrf – – 10.0 ns –
VS Frequency tv 15.85
–
16.68
262.5
17.51
–
ms
H
59.94 Hz
(typ.)
Display tvd –
–
14.87
234
–
–
ms
H
234 line
–
–
15.25
240
–
–
ms
H
240 line
Pulse-width tvp 158.89
–
190.67
3
–
–
ms
H
–
Pulse-width
+back-porch
tvpb –
–
1.33
21
–
–
ms
H
–
Rise/fall tvrf – – 10.0 ns –
Analog
R, G, B
Setup time tdas 10.0 – – ns –
Hold time tdah 10.0 – – ns –
Note In the display start period (pulse-width + back-porch), analog RGB signals should be blanking level.
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
(d) PAL, external CLK
Parameters Symbols Min. Typ. Max. Unit Remarks
EXTCLK Frequency 1/tc –
118.75
8.0
125.00
–
131.25
MHz
ns
–
Rise/fall tcrf – – 10 ns –
Duty tch/tc 0.4 0.5 0.6 – –
HS Frequency th 60.80
–
64.00
512
67.20
–
ms
CLK
15.625 kHz
(typ.)
Display thd –
–
40.00
320
–
–
ms
CLK
–
Pulse-width thp 1.0
–
4.7
38
–
–
ms
CLK
–
Pulse-width
+back-porch
thpb –
–
9.63
77
–
–
ms
CLK
234 line
–
–
10.25
82
–
–
ms
CLK
240 line
CLK-Hsync timing
hold/setup time
thch 10.0 – – ns –
thcs 10.0 – – ns –
V-Hsync timing
hold/setup time
thvh 1 – – CLK –
thvs 10.0 – – ns –
Rise/fall thrf – – 10.0 ns –
VS Frequency tv 19.00
–
20.00
312.5
21.00
–
ms
H
50.00 Hz
(typ.)
Display tvd –
–
17.47
273
–
–
ms
H
234 line
–
–
17.92
280
–
–
ms
H
240 line
Pulse-width tvp 153.60
–
192.00
2.5
–
–
ms
H
–
Pulse-width
+back-porch
tvpb –
–
1.86
29
–
–
ms
H
234 line
–
–
1.66
26
–
–
ms
H
240 line
Rise/fall tvrf – – 10.0 ns –
Analog
R, G, B
Setup time tdas 10.0 – – ns –
Hold time tdah 10.0 – – ns –
Note In the display start period (pulse-width + back-porch), analog RGB signals should be blanking level.
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
(2) DEFINITION OF INPUT SIGNAL TIMING
tc
*
VIH
CLK 1.5 V
*
VIL
R
G
B
*
VIH
HS 1.5 V
*
VIL
thrf
tch
tcrf
tdas tdah
thch thcs
*
VIH
VS 1.5 V
*
VIL
tvrf
VIH *
1.5 V
VIL *
VIH *
1.5 V
VIL *
HS
thvh thvs
* VIH = 3.15 V (min.) to 5.00 V (max.)
VIL = 0.00 V (min.) to 0.90 V (max.)
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
tv
tvp
VS
tvb
Display period
tvpb
tvd
th
thp
HS
thb
Display period
thpb
thd
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
OPTICAL CHARACTERISTICS
(Ta = 25°C, VDC = 12 V, VDCB = 12 V) Note 1
Item Symbol Condition Min. Typ. Max. Unit Remark
Contrast ratio CR Note 2 70 85 – – Note 3
Luminance Lvmax Note 2 200 250 – cd/m2 Note 4
Luminance uniformity – max./min. – – 1.5 – Note 5
Reference data
(Ta = 25°C, VDC = 12 V, VDCB = 12 V)
Item Symbol Condition Min. Typ. Max. Unit Remark
Contrast ratio CR q x = ±0°, q y = –5° 80 100 – – Note 3
Viewing angle range q x+ CR > 10, q y= –5°
white/black
40 45 55 deg. Note 6
q x– 40 45 55 deg.
q y+ CR > 10, q x = ±30°
white/black
18 30 35 deg.
q y– 10 15 25 deg.
Color gamut C q x = ±0°, q y = ±0° to NTSC 40 50 – % –
Response time Ton white to black – 16 30 ms Note 7
Toff black to white – 44 60 ms Note 7
Luminance control range – max. = 100% 10 – 100 % Note 8
Notes 1. Ta = 25°C, VDC = 9.5 V, VDCB = 9.5 V
2.
Viewing angle is q x = ±0°, q y = ±0°. At center.
3.
The contrast ratio is calculated by using the following formula.
Luminance with all pixels in "white”
Contrast ratio (CR) =
Luminance with all pixels in "black”
The luminance is measured in a darkroom.
4.
The luminance is measured after 20 minutes from the module works, with all pixels in "white”. The typical
value is measured after luminance saturation.
50cm
Photo-detector(TOPCON BM-5A)
LCD module
1°
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
Notes 5. The measurement-point of Brightness (Luminance) uniformity.
2 3
5 4
1
Column
80 160 240
Line
60
180
120
6. Definitions of viewing angle are as follows.
Perpendicular
q x- q y+ q y- - x
- y
+ y
q x+ + x
12 o’clock
7.
Definitions of response time is as follows.
Photo-detector output signal is measured when the luminance changes "white” to "black” and "black”
to "white”. Response time are Ton and Toff of the photo-detector output amplitude. Ton is the time
between 100% and 10%. Toff is the time between 0% and 90%.
100%
White
Black
0%
Luminance
10%
Ton Toff
90%
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
8. The pulse signal for luminous control needs to feed BPLS-pin in the white-color data. (CMOS level)
3.5 to 5.0 V (H level)
0 to 0.5 V (L level)
(A)
(B)
Recommendation: (A) = 500 ms to 3.7 ms
(B) = 3.7 ms ± 10%
Pulse (A) duty 100%: Relative luminance is 100%
Pulse (A) duty 20%: Relative luminance is 10% (reference value)
The luminance control function works more than 10°C
Luminance control returns default (factory set) for the stability of the lamp operation when the
LCD is less than 10°C.
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
RELIABILITY TEST SPECIFICATIONS
No. Test item Test condition Judgement
1 High temperature (operation) <1>
<2>
<3>
85 ± 2°C at the display area
192 houres
Others are based on JASO-D001-94.
Note 1
2 Low temperature (operation) <1>
<2>
<3>
–30°C ± 4°C at the display area
192 houres
Others are based on JASO-D001-94.
Note 1
3 High temperature (non-operation) <1>
<2>
<3>
95°C ± 2°C
192 houres
Others are based on JASO-D001-94.
Note 1
4 Low temperature (non-operation) <1>
<2>
<3>
–40°C ± 4°C
192 houres
Others are based on JASO-D001-94.
Note 1
5 High temperature/Humidity
(operation)
<1>
<2>
<3>
60°C ± 2°C, 90% relative humidity
192 houres
Others are based on JASO-D001-94.
Note 1
6 Heat - Humidity cycle
(operation)
<1>
<2>
<3>
First step : 23 ± 2°C, 65% relative humidity,
4 hours
Second step : 55 ± 2°C, 97% relative humidity,
10 hours
Third step : –40 ± 4°C, 2 hours
no-humidity arrangement
Fourth step : 85 ± 2°C, 2 hours
no-humidity arrangement
10 cycles, 24 hours/cycle (Note 2)
Others are based on JASO-D001-94.
Note 1
7 Heat cycle (operation) <1>
<2>
<3>
First step : 75 ± 2°C, 2 hours
Second step : –30 ± 4°C, 2 hours
35 cycles, 8 hours/cycle (Note 3)
Others are based on JASO-D001-94.
Note 1
8 Thermal shock (non-operation) <1>
<2>
<3>
First step : 95 ± 2°C, 2 hours
Second step : –40 ± 4°C, 2 hours 1 cycle
50 cycles
Others are based on JASO-D001.
Note 1
9 Vibration (non-operation) <1>
<2>
<3>
<4>
5 to 200 Hz, 29.4 m/s2 (3G)
10 min/sweep
X and Y direction : 2 hours
Z direction : 4 hours
Others are based on JASO-D001.
Note 1
Note 4
JASO: Japanese Automobile Standards Organization
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
No. Test item Test condition Judgement
10 Mechanical shock (non-operation) <1>
<2>
<3>
980 m/s2 (100G), 11ms
X, Y and Z direction: 3 times each direction
Others are based on JASO-D001.
Note 1
11 ESD (operation) <1>
<2>
<3>
150 pF, 150 W, ± 10 KV
9 points on a panel
10 times/point, at an interval of 1 second
Note 1
Note 4
12 Dust (operation) <1>
<2>
15 kinds of dust (JIS-Z 8901)
15 s/stir, 8 times
Note 1
JIS: Japanese Industrial Standards
Notes 1. Display function is checked by the same condition of the out-going inspection.
2. Refer to Heat/Humidity cycle pattern (See the next page).
3. Refer to heat cycle pattern (See the next page).
4. Discharge points are shown as follow.
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
Temp.
0 4 4.5 14.5 17 19 22.5 24
20.5
85°C
55°C
23°C
[H]
–40°C
Relative Humidity 65%
97%
No humidity
arrangement
0 4 4.5 14.5 17 19 22.5 24 [H]
20.5
Operation
Non-
Operation
(Black display)
operation
(Black display)
One cycle
Note 2 Heat/Humidity cycle pattern
Non-
operation
One cycle
1H 2H 1H 1H 2H 2H
–30°C
75°C
Operation
(Black display)
Operation
(Black display)
Note 3 Heat cycle pattern
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
GENERAL CAUTIONS
Next figures and sentence are very important, Please understand these contents as follows.
CAUTION This figure is a mark that you will get hurt and/or the module will have damages when
you make a mistake to operate.
This figure is a mark that you will get an electric shock when you make a mistake to operate.
This figure is a mark that you will get hurt when you make a mistake to operate
CAUTION
Do not touch an inverter, on which is stuck a caution label··· while the LCD module is under the operation,
because of dangerous high voltage.
(1) Caution when taking out the module
a) Pick the pouch only, when taking out the module from a slipping box.
(2) Cautions for handling the module
a) As the electrostatic discharges may break the LCD module, handle the LCD module with care against
electrostatic discharges.
b)
As the LCD panel and backlight element are made from fragile glass material, impulse and pressure
to the LCD module should be avoided.
c) As the surface of polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning.
d) Do not pull the interface connectors in or out while the LCD module is operating.
e) Put the module display side down on a flat horizontal plane.
f) Handle connectors and cables with care.
g) When the module is operating, do not lose EXTCLK, HS, or VS signal. If any one of these signals is lost,
the LCD panel would be damaged.
(3) Cautions for the atmosphere
a) Dew drop atmosphere should be avoided.
b) Do not store and/or operate the LCD module in a high temperature and/or high humidity atmosphere. Storage
in an Electro-conductive Polymer Packing Pouch and under relatively low temperature atmosphere is
recommended.
c) This module uses a cold cathod fluorescent lamp. Therefore, the life time of the lamp becomes short
conspicuously at low temperature.
d) Do not operate the LCD module in high magnetic field.
(4)
Caution for the module characteristics
a) Do not apply the fixed patterns data signal to the LCD module at product aging.
In order to avoid image
sticking, do not display with fixed pattern. Periodic change of display pattern is recommended.
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
(5)
Other cautions
a) Do not disassemble and/or reassemble LCD module.
b) Do not readjust variable resistors nor switches, etc.
c) When returning the module for repair etc., pack the module not to be broken. We recommend the original
shipping packages.
Liquid Crystal Display has the following specific characteristics. There are not defects or malfunctions.
The display condition of the LCD module may be affected by the ambient temperature.
The module has cold cathode tube for backlighting. Optical characteristics, like luminance or
uniformity, will change during time.
Uneven brightness and/or small spots may be noticed depending on different display patterns.
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
OUTLINE DRAWING (Unit in mm) Front view
(118.0)
134.0 ± 0.5
23 MAX.
NL3224AC35-**
Name plate
(Active area : 111.36)
(2.25)
(Active area : 83.52)
(89.5)
110.0 ± 0.5 Active area centerModule center
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
OUTLINE DRAWING (Unit in mm) Rear view
86.0 ±0.1
111.0 ±0.1
(54.4)
86.0 ±0.1
(13)
1 30
High voltage caution label
Disposal method labelBar code label
4-M3.0Mounting holesDepth 4 mm
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
Data Sheet EN0495EJ1V1DS00
NL3224AC35-01, 13
No part of this document may be copied or reproduced in any form or by any means without the prior written
consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in
this document.
NEC Corporation does not assume any liability for infringement of patents. Copyrights or other intellectual
property rights of third parties by or arising from use of a device described herein or any other liability arising
from use of such device. No license, either express, implied or otherwise, is granted under any patents,
copyrights or other intellectual property rights of NEC Corporation or of others.
While NEC Corporation has been making continuous effort to enhance the reliability of its Electronic
Components, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury
to persons or property arising from a defect in an NEC Electronic Components, customers must incorporate
sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features.
NEC devices are classified into the following three quanlity grades:
"Standard", "Special", and "Specific". The Specific quanlity grade applies only to devices developed based on
a customer designated "quality assurance program" for a specific application. The recommended applications
of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each
device before using it in a particular application.
Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio
and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial
robots.
Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life
support)
Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support
system or medical equipment for life support, etc.
The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books.
If customers intend to use NEC devices for applications other than those speci fied for Standard quality grade,
they should contact an NEC sales representative in advance.
Anti-radioactive design is not implemented in this product.
Bu ürüne ilk yorumu siz yapın!